when releasing PUCCH/SRS (see 5.3.13 in 36.331) we need to reset the SR config as well.
In our case, SR is handled by MAC so we need to (re-)configure MAC, not all of
MAC though, just SR.
* Fix deadlock caused by update_measurements calling in_sync
* Fix overlapping SRS condition
* Do not use shortened PUSCH in transmissions and retx from RAR
* Revert "Fix deadlock caused by update_measurements calling in_sync"
This reverts commit f58c8c8c766f8f95baa3a3bf8287d8e25b2057ba.
* Make PHY non-blocking and fefactor HO procedure
* makes entire PHY non-blocking through command interface
* adds dedicated queue for cell_search/cell_select commands
* refactor HO procedure to run faster, in one stack cycle. Looks closer to the specs
* force ue to always apply SIB2 configuration during reestablishment
* Run update_measurements in all workers
Co-authored-by: Ismael Gomez <ismagom@gmail.com>
* add locked and unlocked version of has_data() since one is
called from stack and one from PHY threads
* add comments in each interface section as to why locking
is required or not
* remove RLC rwlock when not required
* move calls only used by RRC to RRC section
this patch refactors the SDU queuing and dropping policy of the RLC and PDCP layer.
the previous design had issues when packets have been generated at a higher
rate above the PDCP than they could be consumed below the RLC.
When the RLC SDU queues were full, we allowed two policies, one to block on the write
and the other to drop the SDU. Both options are not ideal because they either
lead to a blocking stack thread or to lost PDCP PDUs.
To avoid this, this patch makes the following changes:
* PDCP monitors RLC's SDU queue and drops packets on its north-bound SAP if queues are full
* a new method sdu_queue_is_full() has been added to the RLC interface for PDCP
* remove blocking write from pdcp and rlc write_sdu() interface
* all writes into queues need to be non-blocking
* if Tx queues are overflowing, SDUs are dropped above PDCP, not RLC
* log warning if RLC still needs to drop SDUs
* this case should be avoided with the monitoring mechanism
extend GW-NAS interface to signal test mode activation.
The method is a noop in the normal GW but is implemented in
the TTCN3 DUT according to TS 36.509 for Mode B
this is to better differentiate from "send_attach_request" that
only packs and send the actual attach request message. The
entire attach procedure may include PLMN search, etc.
previously PDCP security (integrity and ciphering) could only
be enabled for both Rx and Tx at the same time.
this, however, caused an issue during the conformance testing in which,
in TC_8_2_1_1() for example, the eNB sends a SecModeCommand and a
RRC Reconfiguration in the same MAC TB. In this case, the eNB
needs to be able to enable DL security right after sending the SecModeCmd
in order to send the RRCReconfig encrypted. However, enabling UL security needs
to be postponed until after the SecModeComplete is received.
This patch allows to enable PDCP security for rx/tx independently if
that is needed. The default way is like before, enabling it for tx/rx at
the same time.
rrc_meas refactor. Need to split commit
Fix typo
Temporal commit
Apply rx_gain_offset to neighbour cell measurements
srsLTE: modify TESTASSERT Macro to follow codeline
SRSUE: prevent RRC from having serving cell in neighbour list
SRSUE: DL HARQ does not need Time Aligment Timer. UL is disabled using PUCCH resources release
SRSUE: extend intra-frequency to CA SCell
SRSUE: fix confusing/ambiguous code in the RRC measurements and fix concurrency issue
SRSUE: remove RRC measurement report triggers when measurements are modified or HO succesful
SRSUE: fix compilation issues and Reest SIB indexes
Fixes sync using incorrect cell configuration when search cell does not find a correct cell
Small refactor to remove measurement report triggers always after removing measurement
SRSUE: Removed SIC PSS from UE
SRSUE: fix inter-frequency reestablishment and added more traces
SRSUE: Fix compilation issue